20.309:Homeworks/Homework1

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(Question 6)
Line 45: Line 45:
==Question 6==
==Question 6==
-
Consider the op-amp circuit shown in Fig. 3 which was first introduced in Lab Module 0.
+
Lab module 0 introduced the op-amp circuit shown in Fig. 3.
-
[[Image:Hw1invopamp.JPG|250px|center]]<br>
+
[[Image:Hw1invopamp.JPG|250px|center]]<br/>
-
<center>Figure 3: An inverting op-amp circuit.</center>
+
<center>'''Figure 3: Inverting Voltage Amplifier'''</center><br/>
-
(a) Calculate the gain of this circuit, ''V<sub>out</sub>/V<sub>in</sub>''.
+
(a) Calculate the gain of this circuit, ''V<sub>out</sub>/V<sub>in</sub>'' in terms of the input voltage and the two resistor values.
-
(b) At times, the signal you may be interested in measuring is in the form of a current, such as in the upcoming DNA melting curve lab. An example circuit for measuring a current is a transimpedance amplifier shown in figure 3.  Determine an expression for the output voltage of the circuit with respect to a DC current input. Express your answer in ''V<sub>out</sub>/I<sub>in</sub>''. <br>
+
[[Image:SimpleTransimpedenceAmplifier.jpg|250px|center]]<br/>
 +
<center>'''Figure 4: Transimpedence Amplifier'''</center><br/>
-
[[Image:Hw1highgopamp.JPG|thumb|250px|center|Figure 4: high gain transimpedance amplifier]]<br>
+
(b) In the DNA melting lab, fluorescence intensity will be determined by measuring the current output of a photodiode.  Figure 4 shows a circuit that converts a current to a voltage called a transimpedance amplifier. 
 +
 
 +
Determine an expression for the output voltage of the circuit produced by a DC current input at ''i<sub>in</sub>''. Express your answer in the form of a transfer function, ''V<sub>out</sub>/I<sub>in</sub>''.
 +
 
 +
(c) A transimpedence amplifier with a gain of approximately 10<sup>8</sup> V/A will be required for the DNA lab. What value of resistor in the circuit of Figure 4 would achieve this gain?
 +
 
 +
(d) It is undesirable to use the large values of resistors you computed in part C. The circuit in Figure 5 shows another possible implementation of the transimpedence amplifier. Derive an expression for the output voltage of the circuit in figure 5 in terms of the input current and the three resistor values.
 +
 
 +
[[Image:Hw1highgopamp.JPG|250px|center|Figure 4: high gain transimpedance amplifier]]<br/>
 +
<center>'''Figure 4: High gain transimpedance amplifier'''</center><br/>
(c) Since this is such a high-gain circuit, it can be quite noisy, if the input current ''I<sub>in</sub>'' experiences high-frequency fluctuations. You can insert a capacitor to reduce the noise (i.e. make a low-pass filter to eliminate high-frequency content). Where would you insert it, and how would you choose its size? <br>
(c) Since this is such a high-gain circuit, it can be quite noisy, if the input current ''I<sub>in</sub>'' experiences high-frequency fluctuations. You can insert a capacitor to reduce the noise (i.e. make a low-pass filter to eliminate high-frequency content). Where would you insert it, and how would you choose its size? <br>

Revision as of 15:24, 5 September 2007

20.309 Fall Semester 2007
Homework Set 1
Due by 12:00 noon on Friday Sept. 21, 2007


Contents

Question 1

Figure 1 shows a resistor network known as a Wheatstone bridge. Part of the apparatus which you'll build shortly for the DNA melting curves module involves half of a "bridge". This is a common circuit used to measure the resistance of an unknown value, Rx. For now, we will look at it analytically. Rx is a resistance you are trying to measure, and R3 is a variable resistor.


Figure 1: A Wheatstone bridge circuit.

(a) Assuming R3 is set such that the bridge is balanced (i.e. Vab=0), derive an analytical expression for Rx in terms of R1, R2 and R3.

(b) Now let R3 also be a fixed value, and suppose that Rx varies in a way that makes Vab nonzero. Derive an expression for the current that would flow if you connected an ammeter from a to b. Assume the ammeter has zero internal resistance.


Question 2

Referring again to the Wheatstone Bridge in Figure 1, suppose that Rx varies with some physical parameter (strain, temperature, etc.) in the range of 1-10kΩ. You want to use the circuit to measure the physical variable by observing Vab=0 and correlating it to the resistance changes. In what range should the values of R1, R2 and R3 be to make a sensitive measurement? Explain your reasoning. (Hint: using matlab to plot the output as a function of the varying resistances is a very useful way to think about this problem).


Question 3

Photodiode i-v characteristics: Using the data that you collected in the lab for the photodiode, generate 3-4 i-v curves for a photodiode at different light levels (including in darkness). Plot these on the same graph to see how incident light affects diode i-v characteristics.
Give a brief (qualitative) explanation for why photodiodes are best used in reverse bias?


Question 4

Transfer functions: For the black boxes that you measured in the lab, determine what kind of circuit/filter each one is (two of them will look similar, but have an important difference - what is it?). Determine a transfer function that can model the circuit, and fit the model to the data to see whether the model makes sense.
Of the four boxes, "D" is required, and you should choose one of either "A" or "C". You can fit "B" for bonus credit.


Question 5

Referring to the circuit shown in Figure 2, what value of RL (in terms of R1 and R2) will result in the maximum power being dissipated in the load?
(Hint: this is much easier to do if you first remove the load, and calculate the equivalent Thevenin output resistance RT of the divider looking into the node labeled Vout. Then express RL for maximal power transfer in terms of RT.


Figure 2: A voltage divider formed by R1 and R2 driving a resistive load RL.


Question 6

Lab module 0 introduced the op-amp circuit shown in Fig. 3.


Figure 3: Inverting Voltage Amplifier

(a) Calculate the gain of this circuit, Vout/Vin in terms of the input voltage and the two resistor values.


Figure 4: Transimpedence Amplifier

(b) In the DNA melting lab, fluorescence intensity will be determined by measuring the current output of a photodiode. Figure 4 shows a circuit that converts a current to a voltage called a transimpedance amplifier.

Determine an expression for the output voltage of the circuit produced by a DC current input at iin. Express your answer in the form of a transfer function, Vout/Iin.

(c) A transimpedence amplifier with a gain of approximately 108 V/A will be required for the DNA lab. What value of resistor in the circuit of Figure 4 would achieve this gain?

(d) It is undesirable to use the large values of resistors you computed in part C. The circuit in Figure 5 shows another possible implementation of the transimpedence amplifier. Derive an expression for the output voltage of the circuit in figure 5 in terms of the input current and the three resistor values.

Figure 4: high gain transimpedance amplifier

Figure 4: High gain transimpedance amplifier

(c) Since this is such a high-gain circuit, it can be quite noisy, if the input current Iin experiences high-frequency fluctuations. You can insert a capacitor to reduce the noise (i.e. make a low-pass filter to eliminate high-frequency content). Where would you insert it, and how would you choose its size?
(d) Now write down the expression for this new circuit's output with respect to the current input for AC signals (Hint: in the expression from part (a), substitute the parallel combination RL\parallelC for the resistor Rx that you chose).

Personal tools