BISC219/F12: RNAi Lab 10

From OpenWetWare

Revision as of 08:27, 13 November 2012 by Tucker Crum (Talk | contribs)
Jump to: navigation, search

Lab 10: Series 3 Investigation of Gene Regulation Using RNAi

Preparation of the Na+ gradient in the Chemotaxis Assay media
The day before lab your instructor will add the chemicals needed to prepare the chemotaxis assay plates.

  1. 10 μL of 2.5M NaCl is added to the Na dot you drew on your plate. Once the NaCl is absorbed the Na+ ions will disperse in a gradient away from the dot. The Cl2 is not in a gradient due to the addition of MgCl2 to the media during initial preparation.
  2. 10 μL of sterile water is added to the W dot you drew to serve as a negative control.



Harvesting the C. elegans
Thoroughly washing the worms to remove any residual food and media is critical for the chemotaxis assay to work properly.

  1. Label 2 15 ml conical tubes with wild type - treated
  2. Label 2 15 ml conical tubes with rrf-3- treated
  3. Label 1 15 ml conical tubes with wild type - control
  4. Label 1 15 ml conical tubes with rrf-3 - control
  5. Label 2 15 ml conical tubes with lsy-2 mutant
  6. Wash the worms off of each RNAi feeding plate 3x with 5 ml ice cold sterile water (kept in your ice bucket) into separately labeled 15ml conical tubes-- store the tubes with worms in them on ice.
  7. Once all the worms are collected, put the caps on the tubes and invert a few times to mix the worms.
  8. Let the worms settle to the bottom of the tubes (keep them in the ice bucket!) - about 10 minutes
  9. Remove all but 1 ml of the water with a disposable Pasteur pipette.
  10. Add iced cold sterile water to 15 ml in each tube and cap the tubes again. Invert and let the worms settle.
  11. Remove all but 1 ml of the cold water with a disposable Pasteur pipette.
  12. Transfer the remaining 1 ml of cold water + worms to a sterile 1.5 ml microfuge tube.
  13. Spin the worms at 10,000 rpm for 1 minute to pellet.
  14. Remove all but approximately 50μL of worms and water at the bottom of the tube.
  15. Using a razor blade, cut the end off of a micropipette tip (this will prevent the pellet of worms from being damaged).
  16. Pipette the entire pellet of worms to the appropriate assay plate, placing the worms gently on the central 2 cm circle.
  17. Wick away any extra water with the corner of a Kimwipe but do not remove your worms!



While the C. elegans are settling: Add 3 μL of 0.25M sodium azide to the Na and W dots on your chemotaxis assay plates. The sodium azide will immobilize the worms who move close to the dots.

The Assay:

  1. The worms are allowed to move around each plate for 1 hour
  2. Take a photograph of each of the plates (rrf-3 from RNAi Feeder and HT115(DE) control plates; N2 from RNAi Feeder and HT115(DE) control plates; and lsy-2 mutants) at the end of the hour using one of the lab digital cameras or your own camera held to the eye piece of the microscope. Make sure you carefully organize each plate so that the photos have the quadrants in the same comparative position.
  3. At the end of the hour (after photographing the plates), the worms in the two quandrants nearest the Na dot are counted and compared to the number in the two quandrants near the W dot. Counting is best done by inverting the plates. Use your dissecting scope and a Sharpie to make a dot on the plastic surface of the plate where every worm you see is located. Then count the dots/quandrant and record the numbers of worms on each quandrant in the google doc data spread sheet in the Project 3 folder in Resources in Sakai. Your instructor will have that spreadsheet open on a computer in the back of the lab. Add the numbers of worms in quandrants 1&2 (Na) and compare that total to the number in quandrants 3&4 (Water). Make conclusions about general trends in the worm distribution and record those notes in your lab notebook.
  4. With a different color sharpie for each strain circle the area of the plate containing the greatest concentration of worms - generally this shape will be a circle or oval. If there is no particular area with a greater concentration do not make any mark.
  5. Take a second set of photographs (one per strain of worm: N2, rrf-3 or mutant) using the BIORAD imager (Directions below). Arrange the plates for each strain so that the position of the control plates vs. RNAi treated plates is the same among the photos and that the quandrants are positioned the same in all plates.


Capturing Digital Images Using the BioRad Imaging System in L308

Instructions for Taking a DNA gel image stained with Sybr Safe using the BioRad ChemiDoc MP System with Image Lab Software

Quick and Easy Protocol for photographing your chemotaxis experiment plates:
1) Make sure the Power Button on the right front of the imager shows a green light. If not press it until the green light comes on and wait 5-10 min for warm up.

2) Open the UV transilluminator drawer on the lower front of the imager and Position the 3 plates of one strain (N2 or rrf-3or the 2 plates of the lsy-2 mutant) in the drawer so that the quandrants in each plate are aligned in the same way.

3) Close the drawer.

4) Open the ImageLab 4.0.1 software (not the Help icon) by double clicking on the icon on the computer desktop

5) Find and open the Recent Protocol called Protocol Chemotaxis 219. Double click to open it.

6) Click Run Protocol (green button) to take the photo.

7) When your image appears it will have blue stripes across it. Go to the square rainbow icon and open it. Change from Stain Free to Gray and click Ok. You can adjust the contrast, etc. by opening the black and white sun icon.

8) To Save your image, find the BISC219 F12 folder on the Desktop and open it and the folder for your lab section. go to File---Export---Export for Publication (use the defaults, e.g. 300dpi). Check the Location where your image will be saved (make sure it's your lab sections'), change the FILE Name to the strain name and your team color, and use the drop down menu to SAVE AS TYPE tiff or jpg. Click Save.

9) Remove your plates and repeat with the plates of the next strain. Make sure that you align the plates (RNAi vs. control and quandrant 1 at the top left) exactly as you did the other strain's plates so that the images are easily comparative.

10) Close the Image Lab Software

11) When all 3 strains have been photographed, Remove your last set of plates.

12) Open Internet Explorer and upload your saved images to the Data folder in Resources in Sakai under Project 3 Chemotaxis Images.

13) The computer AND the ChemiDoc Imager should remain ON. DO NOT Turn OFF the power or shut down or log off the computer.

Personal tools