Lab 2: Gene Mapping
Lab 3: Linkage Test Part 1
Lab 4: Linkage Test Part 2 and Mapping
Lab 5: Mapping Part 2
Lab 6: SCORE!
Mapping: Count all adult and L4 progeny from one plate, scoring as either wild type , Dpy , Unc or Dpy Unc. Also score the second plate unless you have counted >100 total animals. Remember to remove each animal after you have determined its phenotype.
How would you get the single mutant class if you started with linked genes d u/+ +?
You will determine map distances using the formula: RF (recombinant frequency) =the number of single mutants (both dpy and unc single mutants) divided by the total number of worms counted * 100 (to obtain RF in % recombinants and thus in map units).
Congratulations! You now have an idea about the location and, maybe, the name of your MB? dpy mutation. To learn more you can enter the gene name (if you found an allelic association through your complementation analysis and now know the gene name)into the C. elegans database: | Wormbase at http://www.wormbase.org Wormbase.
Click on the link to Wormbase above and enter your dumpy gene name into the box at the top of the page and click Search. It will either bring you directly to that page or it will bring you to a page with mutiple hits - click on the link that provides a definition for what the gene does.
On this new page should be all the known information about this particular gene. Its name, who named it, what the gene encodes - if that is known, and much more. At the bottom will be a list of references - or a link to a list of references. Check this out. Does it appear that you are working with a new gene or one that has been well characterized?
If you aren't sure of your dumpy gene name because found complementarity with all of the 4 dumpy reference strains or other confusing complementation results, you can find out more about your dumpy gene on Wormbase from the location of your linked unc gene. You can start looking up the unc reference gene. Since you know that your dumpy gene is on the same chromosome and is a certain number of map units away from this known unc reference gene; therefore, you might can use location information about the genes around your linked unc gene to see if there is a well characterized dumpy gene in the position you have mapped it (+/- the number of map units) on that chromosome. Enter the unc reference gene name in Wormbase and click on Mapping Data. Scroll down the page until you find the mapping data for that gene and see if there is a known dumpy gene at the location you have mapped your mutation relative to this unc gene. If there is, you now know the name of your dumpy gene and you can enter that gene name in Wormbase to learn more about it. If you find no known dumpy associated gene at this map location, it is possible that you have found a new dumpy gene or a new function for an otherwise characterized gene. Your next step would be to see what is known about that location on the chromosome and see if what's known fits in at all with your observations. If it does, great and, if not, you have some thinking to do. DO NOT write a paper about "sources of error" in your experimental design!!!!
Spend some time with Wormbase and marvel at all the hard work and years of research that went into discovering all this information about this tiny little nematode that causes us no harm (non-parasitic). Why do you think so many smart people have devoted so much of their time and energy to working out the genetics of "appearance or movement challenged" little worms? We will talk more about model organisms and the power of functional and comparative genomics in our next series.
Sequencing a portion of our genes of interest will provide us with direct evidence of the nature of the mutation (i.e: point mutation or deletion) in the mutant worms. It will help us make conclusions whether or not this mutation has been previously characterized or not. This knowledge will be useful to establish a link with the type of functional defect present in the protein produced by the mutated gene.
There are three major steps in a sequencing reaction, which are repeated for 25 cycles in a thermocycler:
- Denaturation at 94°C: During the denaturation, the double strand melts open to single stranded DNA and all enzymatic reactions stop, including the extension from the previous cycle.
- Annealing at 50°C: In each sequencing reaction, a specific primer is required. This primer is a short sequence of bases complementary to a region of the plasmid upstream of the target gene. The primer will anneal and stay, we hope, only at one position on the single stranded DNA template. In sequencing reactions there is only one strand copied whereas, in PCR, two primers are used so both strands of the DNA template are copied. The primer jiggles around, caused by the Brownian motion. Ionic bonds are constantly formed and broken between the single stranded primer and the single stranded template. The more stable bonds last a little bit longer (primers that fit exactly) and on that small section of double stranded DNA (template and primer), the polymerase can attach and starts copying the template. Once there are a few bases built in, the ionic bond is so strong between the template and the primer, that it does not break anymore.
- Extension at 60°C: Sixty degrees is the ideal working temperature for polymerase activity in sequencing even though, normally, it is 72 °C. Because the growing strand must incorporate ddNTP's which are chemically modified with a fluorescent label, the temperature is lowered so it has time to incorporate the 'strange' molecules. Well designed primers, where there are a few bases built in, already have a stronger ionic attraction to the template than the forces breaking these attractions. Primers that are on positions with no exact match, come loose again and don't give an extension of the fragment. The bases (complementary to the template) are coupled to the primer on the 3'side (adding dNTP's or ddNTP's from 5' to 3', reading from the template from 3' to 5' side, bases are added complementary to the template). When a ddNTP is incorporated, the extension reaction stops because a ddNTP contains a H-atom on the 3rd carbon atom (dNTP's contain a OH-atom on that position). Since the ddNTP's are fluorescently labeled, it is possible to detect the color of the last base of this fragment on an automated sequencer.
Because only one primer is used, only one strand is copied during sequencing, there is a linear (not log as in PCR) increase of the number of copies of one strand of the gene. Therefore, there has to be a large number of copies of the gene in the starting mixture for sequencing. If there are 1000 copies of the wanted gene before the cycling starts, after one cycle there will be 2000 copies: the 1000 original templates and 1000 complementary strands with each one fluorescent label on the last base. After two cycles, there will be 2000 complementary strands, three cycles will result in 3000 complementary strands and so on.
What your instructor did for you:
Due to time restraints your instructor completed the sequencing for you and it is your job to analyze the results of the sequencing reaction.
Steps in sequencing a C. elegans gene:
1. Digest the tough outer cuticle.
Add worms to a mixture of 10 mM Tris, 50 mM KCl, 1.5 mM MgCl2, pH 8.3, with 10 mg/ml Proteinase K.
; Incubate at 65°C for 1 hour to digest the cuticle and then at 95°C for 15 minutes to denature the Proteinase K.