BME103 s2013:T900 Group1

BME 103 Spring 2013	Home People Lab Write-Up 1 Lab Write-Up 2 Lab Write-Up 3 Course Logistics For Instructors Photos Wiki Editing Help
OUR TEAM Kristi Norris: Protocol Planner Carlos Renteria: Research and Design Specialist Raul Monzolo: Open PCR Machine Engineer Johnny Montez: Open PCR Machine Engineer Robert Sanchez: Research and Design Specialist Group 1 LAB 1 WRITE-UP Initial Machine Testing The Original Design (Add image of the full OpenPCR machine here, from the Week 9 exercise. Write a paragraph description for visitors who have no idea what this is) Experimenting With the Connections When we unplugged (part 3) from (part 6), the machine ... (did what? fill in your answer) When we unplugged the white wire that connects (part 6) to (part 2), the machine ... (did what? fill in your answer) Test Run (Write the date you first tested Open PCR and your experience(s) with the machine) Protocols PCR, or Polymerase Chain Reaction, is a method of amplifying a particular segment of DNA by way of selective replication. If the sequence of the target DNA segment is known, primers can be created from the complimentary base pairs at each end of the target segment. A forward as well as a reverse primer is required so that each double strand of DNA results in two double strands of DNA at the end of each cycle (as Taq DNA Polymerase only works in one direction, it needs a primer at the beginning of both strands in order to copy both). To complete PCR, a DNA sample (containing the target DNA segment) must be mixed with the primers (both forward and reverse as discussed above), Taq DNA Polymerase, dNTP's (free base pairs to be used as the building blocks in the new DNA put together by the polymerase), and MgCl2 (a required substrate for the polymerase to use the dNTP's). This solution is then subject to multiple cycles of varying temperatures. The temperature at each stage is chosen to optimize the desired activity of the various ingredients. First, the solution is heated to 95°C for 3 minutes to denature the double stranded DNA into two single strands. This makes the nucleotides available to attaching to the primers (which are much more abundant in the solution than the initial strands of DNA) when the solution is cooled to 57°C. After 30 seconds, the solution is brought up to 72°C, the temperature at which the activity of Taq DNA polymerase is optimal. This temperature is held for 30 seconds while Taq DNA polymerase attaches to the primers and replicates the DNA. This single cycle results in twice as many strands of double-stranded DNA as was put in. The cycle is repeated 35 times with each temperature being held for 30 seconds each. When sufficient copies of the DNA segment have been made, the temperature is decreased to 4°C to stop the reaction. A step-by-step break down of the procedure follows. Thermal Cycler Program Stage 1 95°C for 3 minutes: Initial DNA strand is separated. Stage 2 35 cycles of the following steps, each with a duration of 30 seconds: 95°C: Double strands of DNA separate. 57°C: Primers attach at ends of target DNA segment. 72°C: DNA polymerase activates and replicates target segment of DNA. Stage 3 Final Hold 4°C for 3 minutes: PCR reaction is stopped. DNA Sample Set-up Two samples of DNA were tested in triplicate. Patient 1's ID number is 29013 and Patient 2's ID number is 13146. The samples for Patient 1 were labeled α1, α2, and α3. Similarly, Patient 2's samples were labeled β1, β2, and β3. Additionally, a positive control (CP) and a negative control (CN) were used. The reaction tubes containing the samples and PCR reaction mix were arranged for PCR reaction as follows: CP α1 α2 α3 CN β1 β2 β3 DNA Sample Set-up Procedure 8 reaction tubes were provided to us, each containing 50μL of PCR reaction mix All reaction tubes were labeled according to the table above in order to avoid swapped results 50μL of each DNA sample Mix was added to the correspondingly labeled reaction tube (using a new pipette tip for each transfer in order to avoid cross-contamination between samples) The reaction tubes were placed into the thermocycler The thermocycler program detailed above was run so that PCR would occur in each reaction tube PCR Reaction Mix Taq DNA polymerase MgCl2 dNTP's DNA Sample/Primer Mix Extracted sample of a particular patient's DNA Forward Primer Reverse Primer Research and Development Specific Cancer Marker Detection - The Underlying Technology Polymerase chain reaction (abbreviated PCR) is the process by which a selected strand or segment of DNA is replicated various times. Each step in the process is vital for the process to occur efficiently. In the first step of PCR where the samples were heated to 95ºC for three minutes, the two strands of DNA were separated from one another due to the high amount of heat in the reaction. This temperature and the amount of time that the samples were heated were both necessary because they allowed for an adequate amount of energy necessary to break the hydrogen bonds between the parallel nucleotides. This caused the DNA sequence to unzip, which opens up the opportunity for the entire reaction to occur. After this occurred, 35 cycles of the samples being heated up to 95ºC, down to 57ºC, down to 72ºC occured. Again, at 95ºC the DNA was separated in order for the individual components to begin mixing together, like a soup. At 57ºC, the samples were cooled down significantly, which allows for the forward and reverse primers to bind to their respective regions. When reheated to 72ºC, the TAQ polymerase was activated which generated a new strand of DNA from both the lagging and leading strands. The primers tell the polymerase where to begin generating new sequences of DNA, with the Magnesium Chloride acting as a catalyst for this reaction. At 72ºC, the temperature is adequate enough to where the polymerase can generate a new strand of DNA from the template quickly without denaturing. After this final step, the new sequences of DNA are fully generated and the process begins over again 35 times, each resulting in two new DNA strands. This helps us because only the cancerous DNA is replicated, whereas the original template DNA is not replicated at all. This is because the primers are designed to bind only to the cancerous sequences of DNA. This is because that specific type of cancer's DNA sequence was analyzed and a primer generated that binds to that analyzed, cancerous sequence. As such, when the primers detect this, they bind to those, and the DNA polymerase begins generated a sequence of DNA for this strand. This does not occur in the normal strand of DNA, simply because it doesn't have that specific sequence, and as such the primers won't bind to it. The mutation in the cancer allows for those specific primers to bind to that sequence, but the opposing, normal strand will not bind to it, even when the strand is continuously copied because the mutation isn't present there. As such, the cancerous sequence will be replicated, while the normal strand remains uncopied.		(BONUS points: Use a program like Powerpoint, Word, Illustrator, Microsoft Paint, etc. to illustrate how primers bind to the cancer DNA template, and how Taq polymerases amplify the DNA. Screen-captures from the OpenPCR tutorial might be useful. Be sure to credit the source if you borrow images.)