Griffitts:Seed scarification and germination: Difference between revisions
From OpenWetWare
Jump to navigationJump to search
mNo edit summary |
m (→Alfalfa) |
||
Line 6: | Line 6: | ||
* Calculate the number of plants you need | * Calculate the number of plants you need | ||
* Weigh out ten times more than the number you need | * Weigh out ten times more than the number you need | ||
** Use GT13R | ** Use GT13R+ | ||
** 1.7 g is approximately 1000 seeds | ** 1.7 g is approximately 1000 seeds | ||
* Place in a smooth sterile flask | * Place in a smooth sterile flask |
Revision as of 09:50, 13 April 2009
Alfalfa
Note: Alfalfa seeds don't need to be scarified
- Calculate the number of plants you need
- Weigh out ten times more than the number you need
- Use GT13R+
- 1.7 g is approximately 1000 seeds
- Place in a smooth sterile flask
- Add 70% ethanol to substantially cover the seeds
- 70% ethanol is next to the scales
- Place on a shaker at room temperature at 150 rpm for 20 minutes
- Decant the ethanol and wash the seeds once with sterile dH2O
- Add Chlorox bleach to substantially cover the seeds
- Place on a shaker at room temperature at 150 rpm for 20 minutes
- Decant the bleach and wash the seeds 4 to 5 times with sterile dH2O
- Add sterile dH2O to substantially cover the seeds
- Place on a shaker at room temperature at 150 rpm for at least 4 hours (preferably 8)
- It's a good idea to wash the seeds with sterile dH2O once during this time
- Decant the sterile dH2O and add fresh sterile dH2O
- Dump into 100×25 mm Petri dishes
- Seeds should be in a monolayer with a small amount of space between them
- Pull off excess water with a pipet
- Tip the plate and give it a few seconds to be sure to get all the excess water
- Wrap plate(s) in Parafilm
- Store upside-down in a drawer for 24 hours
Other Medics
- Place twice as many seeds as you wish to plant into a 50 mL Erlenmeyer flask that has been covered with foil and autoclaved.
- To each of the flasks add 5 mL of sulfuric acid (H2SO4, in the fume hood—be careful!)
- Place on the shaker for the appropriate time (see table below)
- Remove the sulfuric acid
- Discard it into the sulfuric acid waste container in the fume hood
- Immediately rinse the seeds five times with dH2O
- Add 5 mL of bleach
- Place them back onto the shaker for 3 minutes
- Rinse 6–8 times with dH2O
- Pour the seeds and some dH2O into small plates
- Parafilm and store in the fridge 24 hours to allow imbibement
- Be sure not to have excessive amounts of water in the plate
- Remove the seeds from the fridge and remove the water
- Parafilm the mini-plates, invert and place at room temperature in the dark for one day
Note: some plants may take a little longer to germinate
species | time | notes |
---|---|---|
arabica | 15 minutes | |
constricta | 10 minutes | |
disciformis | 10 minutes | |
heyniana | 20 minutes | |
italica | 10 minutes | |
lesinsii | 10 minutes | |
lupulina | 20 minutes | |
polymorpha | 20 minutes | |
praecox | 8 minutes | refrigerate in 15 mL dH2O for 36–48 hours |
rugosa | 30 minutes | |
tenoreana | 10 minutes | |
truncatula A17 | 10 minutes |
Lotus japonicus
- Place twice as many seeds as you wish to plant into a 50 mL Erlenmeyer flask that has been covered with foil and autoclaved.
- To each of the flasks add 5 mL of sulfuric acid (H2SO4, in the fume hood—be careful!)
- Place on the shaker for 20 minutes
- Remove the sulfuric acid
- Discard it into the sulfuric acid waste container in the fume hood
- Immediately rinse the seeds once with dH2O
- Add 5 mL of bleach
- Place them back onto the shaker for 1 minute
- Rinse five times with dH2O
- Pour the seeds and some dH2O into small plates
- Parafilm and store in the fridge 24 hours to allow imbibement
- Be sure not to have excessive amounts of water in the plate
- Remove the seeds from the fridge and remove the water
- Parafilm the mini-plates, invert and place at room temperature in the dark for one day