ISISBio:Protocols/Sortase mediated ligation/Solid support ligation

From OpenWetWare

Jump to: navigation, search



We [1] and others [2] have used Sortase to attach a range of proteins to a small selection of solid supports, mostly resins or polymer beads, but also glass surfaces. Steric hindrance appears to be a significant problem for these ligation reactions so consideration of the spacer between oligoglycine and the solid support is important.

In the case of ligation to solid supports it is generally not possible to raise the concentration of the ligation partner in large excess over that of the target protein. Nonetheless we have generally found that the standard conditions used for small molecule labelling work well. We have not been able to accurately quantify the yield of protein ligated to solid supports, however experiments aimed at determining the depletion of target protein from solution suggest the yields are low. This is not generally a problem as generally relatively low coverages are desired.

Design of solid support

Beaded polymer supports

We have taken two approaches to the preparation of solid supports. Glycidylmethacrylate beads with one, two, or four glycines at the end of an eight carbon spacer were prepared by conventional fmoc solid phase synthesis and the effect of this on ligation yield and rate were followed. There is a clear effect of the number of glycines which we believe to be primarily a steric effect. In general two glycines at the end of a spacer seems the optimal balance of synthetic work and yields. In the case of the Affigel Resin where repeated cycles of deprotection and coupling are not possible due to the chemistry of the resin we have used the random EDC coupling of diglycine onto surface amines. The conditions used are somewhat unorthodox but are likely to lead to relatively short, sparsely packed chains.

Solid planar surfaces

In our published work on glass surfaces we used an aminosilane to modify the glass followed by random coupling of diglycine onto the surface amines using EDC as was used for the Affigel resin. This followed unsuccessful attempts at ligation to H-GnC-OH (n=1,2,4) treated gold surfaces. Attempts to ligate protein to glass surfaces modified with an aminosilane and fmoc-GG-OH, followed by deprotection, were also unsuccessful. By contrast the random coupling of diglycine onto glass modified with an aminosilane was consistently successful.

Overall our experience is that where background binding is not a major concern random coupling of oligoglycine is a convenient route to a glycine modified surface. Where background binding needs to be reduced more sophisticated approaches will be required. The major limitations on the ligation reaction appear to be steric with the direct coupling of ligation parterns onto surfaces generally not providing effective coupling. In these cases a larger spacer is recommended, ideally one that will stand away from the surface of the solid support.

Preparation of spotted arrays

We have attempted to spot ligation solution onto glass surfaces modified as above to prepare arrays. Although in some experiments this appeared to work the amine surface leads to a large background binding and we were unable to consistently show ligation above non-specific binding background to our satisfaction. This would probably be overcome by more sophisticated preparation of the surface to reduce the number of free (non-glycine) amines on the surface. Amine surfaces generally give a poor background binding response. The random co-coupling of a hydroxyacid and amino acid onto the amine surface followed by oligoglcyine coupling and alkaline hydrolysis of esters is one approach that could be explored. An alternative would be an orthogonal protecting group strategy.


  • Sortase A
  • LPETGG-tagged protein target
  • Solid support
  • Sortase buffer

Standard Conditions

  • Target protein: 5 – 200 µM
  • Ligation partner: For GMA beads we have routinely coupled 1 mg of beads with a surface glycine loading of 2-5 µmol.g-1 in 20 – 50 µL reactions. For glass surfaces we have not characterised surface loading but have prepared them as described [##ref###].
  • Sortase A: 50 nM
  • Standard Sortase buffer


Reactions are incubated for around one hour or overnight with shaking (polymer beads) or overnight with rocking (polyer resins and glass surfaces) at room temperature. For the surfaces described in [1] the glass slides were submerged in the ligation reaction and rocked overnight. The supports were then washed thoroughly in


In those reactions where we attempted to spot the ligation reaction onto a surface we spotted 1 – 10 µL onto the surface and incubating overnight in a H2O saturated atmosphere. This appeared to work but was confounded by background binding.


Relevant papers and books

Error fetching PMID 18000537:
Error fetching PMID 17302384:
Error fetching PMID 14995162:
Error fetching PMID 18229923:
Error fetching PMID 17891153:
Error fetching PMID 17432905:
Error fetching PMID 10734144:
Error fetching PMID 10535938:
  1. Error fetching PMID 18000537: [chan07]
  2. Error fetching PMID 17302384: [parthasarathy07]
  3. >


  4. Error fetching PMID 14995162: [mao04]
  5. Error fetching PMID 18229923: [samantaray08]
  6. Error fetching PMID 17891153: [popp07]
  7. Cameron Neylon, Chemtools LaBLog, 29 August 2007


  8. Error fetching PMID 17432905: [pritz07]
  9. Error fetching PMID 10734144: [ton-that00]
  10. Error fetching PMID 10535938: [ton-that99]
All Medline abstracts: PubMed HubMed


Personal tools