Lidstrom:Building with DNA

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(Ligate)
(Ligate)
Line 16: Line 16:
==Ligate==
==Ligate==
-
*add 1 uL of ligase (kit allows 0.1 to 1 uL) to a 50 uL reaction.
+
*add 1 uL of ligase (kit allows 0.1 to 1 uL) to a 20 uL reaction.
*Incubate on counter (~2 hours) or at 16oC overnight.
*Incubate on counter (~2 hours) or at 16oC overnight.
*You can try varying ratios of vector:insert.  Stoichiometries of 1:1, 1:3, 1:6 are common.   
*You can try varying ratios of vector:insert.  Stoichiometries of 1:1, 1:3, 1:6 are common.   
**The BioBricks/Ginkgo manual suggests only 15 minutes of incubation at 37oC; I have not tried this because I have not been in a rush and because it is very short compared to standard practice I hear about via word of mouth.  -[[User:Janet B. Matsen|Janet]] 2/24/12
**The BioBricks/Ginkgo manual suggests only 15 minutes of incubation at 37oC; I have not tried this because I have not been in a rush and because it is very short compared to standard practice I hear about via word of mouth.  -[[User:Janet B. Matsen|Janet]] 2/24/12
-
*There is no need to purify ligated products before transformation.
+
*There is no need to purify ligated products or heat-inactivate ligase before transformation.
==Transform==
==Transform==

Revision as of 15:33, 6 March 2012

Back to Protocols

Contents

Obtain Parts

  • Perhaps you have them already. Perhaps you will make BioBrick or BglBrick parts via PCR.
  • If you make parts via PCR, column purify the product to remove salts, oligos, etc.

Digest with Restriction Enzymes

  • Use 500+ ng of each part, 5 uL of 10X buffer, 0.5 uL of BSA (stabilizes enzymes) and 1uL of each restriction enzyme, and water to 50uL.
  • 37oC 1.5 hrs, 80oC 20 min (if heat inactivation works with your enzymes), then 4oC forever works in Janet's limited experience.
  • Decide if/how to purify:
    • Gel purification removes salts and restriction enzymes, which can increase success with subsequent ligation.
      • If you are cutting an insert out of a plasmid, you need to remove the piece of the plasmid you don't want to ligate. Gel purify in this case so you can select the band with the appropriate size.
      • If you are cutting off small fragments from a PCR product, you can usually column purify because the fragments you cut off are small enough that they don't bind to the column. Recall that column purification has ~90% yield whereas gel purification has ~90% loss. If you are only going to column purify (or skip purification all together) consider running a few uL on a gel to make sure you only have 1 band.
      • Betsy always gel purifies. Amanda usually does but forgot once and it worked.5

Ligate

  • add 1 uL of ligase (kit allows 0.1 to 1 uL) to a 20 uL reaction.
  • Incubate on counter (~2 hours) or at 16oC overnight.
  • You can try varying ratios of vector:insert. Stoichiometries of 1:1, 1:3, 1:6 are common.
    • The BioBricks/Ginkgo manual suggests only 15 minutes of incubation at 37oC; I have not tried this because I have not been in a rush and because it is very short compared to standard practice I hear about via word of mouth. -Janet 2/24/12
  • There is no need to purify ligated products or heat-inactivate ligase before transformation.

Transform

  • transform ~10 uL of the product. There is some left over in case you need to try again.

Screen with Colony PCR

  • See our colony PCR page for details.

Verify with Sequencing

  • See "Sequencing with GeneWiz" page.
Personal tools