Paraffin embedding and sectioning

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(steps)
(tips)
Line 8: Line 8:
== Steps ==
== Steps ==
-
 
* fix tissues with 4% PFA or other fixatives; fixative volume should be 5-10x of tissue volume
* fix tissues with 4% PFA or other fixatives; fixative volume should be 5-10x of tissue volume
* cut fixed tissues into appropriate portions and place in embedding cassettes
* cut fixed tissues into appropriate portions and place in embedding cassettes
Line 21: Line 20:
:* embed tissues into paraffin blocks
:* embed tissues into paraffin blocks
-
* trim paraffin blocks and cut at 3-10 µm (5 µm is commonly used)
+
* trim paraffin blocks to an optimal cutting surface including the sample with a small paraffin frame
-
* place paraffin ribbon or slice in 40-45ºC water bath
+
* cut 3-10 µm slices (5 µm is commonly used); use a brush to draw the section onto the knife holder
-
* fish out swimming paraffin section using glass slides
+
* place paraffin ribbon or slice in 40-45ºC water bath with a 2nd wet brush (it will expand and wrinkles will vanish)
-
* allow sections to air dry for 30 minutes
+
* fish out swimming paraffin section using glass slides and a brush to position the section
-
* bake in 45-50ºC oven overnight
+
* dry sections O/N at 37ºC (lower baking temperatures are better for subsequent antibody detection)
-
:NEVER go higher than 50ºC for sections thicker than 25µm. Otherwise, sections may crack and fall off during staining
+
* paraffin to water:
* paraffin to water:
Line 35: Line 33:
:* rinse in distilled water
:* rinse in distilled water
 +
== Tips ==
 +
* To cut very thin 1-2µm sections cool the block for 30min at -20ºC and cut using without automatic advancing of the block, relying instead on the temperature expansion of the block. A cutting angle of 15ºC is optimal. More acute angle may not cut at all. Larger angles may break off the section.
 +
* Samples for normal histochemical analysis can be dried faster at 45-60ºC for 6-4h. Do not bake sections >25µm at >50ºC or cracks may appear and parts of the sample may fall off during later washes.
== See also ==
== See also ==
Line 42: Line 43:
* [http://en.wikipedia.org/wiki/Paraffin Wikipedia: Paraffin]
* [http://en.wikipedia.org/wiki/Paraffin Wikipedia: Paraffin]
 +
=== Books ===
 +
* [http://books.google.com/books?id=02mLqzXwStUC&pg=RA1-PA564&dq=paraffin+sections&lr=&as_drrb_is=b&as_minm_is=0&as_miny_is=1995&as_maxm_is=0&as_maxy_is=&as_brr=0&ei=-FPDSvLJDqG8zgSjq_j1Aw#v=onepage&q=paraffin%20sections&f=false Cell biology: a laboratory handbook, Volume 1, by Julio E. Celis]
[[Category:Protocol]]
[[Category:Protocol]]
[[Category:Microscopy]]
[[Category:Microscopy]]
[[Category:In vivo]]
[[Category:In vivo]]

Revision as of 08:10, 30 September 2009

Biological samples often need to be solidified to allow fine sectioning. Thin slices improve the access of dyes, probes, and antibodies and reduce the overlay of different cells layers in the z direction. For light microscopy, paraffin wax is the most frequently used hard matrix for cutting.

Contents

Principle

Since paraffin is immiscible with water, the main constituent of tissue, samples need to be dehydrated by progressively more concentrated ethanol baths. This is followed by a clearing agent, usually xylene, to remove the ethanol. Finally, molten paraffin wax infiltrates the sample and replaces the xylene.

Section thickness

Paraffin sections for light microscopy are typically 5 μm thick. Paraffin wax does not provide a sufficiently hard matrix for cutting thinner slices needed for electron microscopy, typically 80-100 nm thick. Here, epoxy or acrylic resins especially for immunohistochemistry are used.

Steps

  • fix tissues with 4% PFA or other fixatives; fixative volume should be 5-10x of tissue volume
  • cut fixed tissues into appropriate portions and place in embedding cassettes
  • dehydrate for paraffin embedding (water to paraffin):
  • 70% ethanol, 2 changes, 1h each
  • 80% ethanol, 2 changes, 1h each
  • 95% ethanol, 2 changes, 1h each
  • 100% ethanol, 3 changes, 1h each
  • xylene or substitute (i.e. Clear Rite 3), 3 changes, 1h each
  • paraffin wax (56-58ºC), 2 changes, 1.5h each
  • embed tissues into paraffin blocks
  • trim paraffin blocks to an optimal cutting surface including the sample with a small paraffin frame
  • cut 3-10 µm slices (5 µm is commonly used); use a brush to draw the section onto the knife holder
  • place paraffin ribbon or slice in 40-45ºC water bath with a 2nd wet brush (it will expand and wrinkles will vanish)
  • fish out swimming paraffin section using glass slides and a brush to position the section
  • dry sections O/N at 37ºC (lower baking temperatures are better for subsequent antibody detection)
  • paraffin to water:
  • deparaffinise sections in 2-3 changes of xylene, 10m each (3 changes of xylene for sections >25µm)
  • hydrate in 2 changes of 100% ethanol for 3 minutes each
  • 1x 95% ethanol, 1 minute
  • 1x 80% ethanol, 1 minute
  • rinse in distilled water

Tips

  • To cut very thin 1-2µm sections cool the block for 30min at -20ºC and cut using without automatic advancing of the block, relying instead on the temperature expansion of the block. A cutting angle of 15ºC is optimal. More acute angle may not cut at all. Larger angles may break off the section.
  • Samples for normal histochemical analysis can be dried faster at 45-60ºC for 6-4h. Do not bake sections >25µm at >50ºC or cracks may appear and parts of the sample may fall off during later washes.

See also

Books

Personal tools