Prbbbb:fusion biobrick construction v1

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(Procedure)
(Procedure)
Line 104: Line 104:
Follow the standard transformation protocol.
Follow the standard transformation protocol.
 +
 +
Note: Standard Top10 cells show rather low transformation efficiencies with In-Fusion products. We have had good experiences with Invitrogen MaxEfficiency DH5alpha cells and others report good results with Clonetech FusionBlue competent cells.
'''VI Screening'''
'''VI Screening'''

Revision as of 10:07, 9 April 2010

Back to all protocols

Contents

Overview

A protocol for creating fusion (Freiburg)-formatted Biobricks from unformatted template DNA.

We use PCR to amplify the insert and to introduce the inner 16 bp of Biobrick prefix and suffix. This insert is then recombined into the linearized vector backbone using Clontech In-Fusion. That means we avoid any restriction or ligation, which saves time and makes this protocol rather reliable.

The same protocol can be applied to other Biobrick formats -- simply replace the primer flanks by the 16 inner-most bases of your favorite prefix and suffix sequence.

Materials

Procedure

I Primer design

  1. design primers to 5' (left) and 3' (right) end of your Biobrick insert using these parameters:
    • desired annealing Temperature: 60-62°C
    • method: nearest neighbor
    • [primer]: 500 nM; [salt]: 50 nM; [MgCl2]: 1.5 mM; [dNTP]: 200 nM
    • try ending with one or two G/C at the 3' terminal
  2. Add the following sequence to the beginning of the forward primer:
    • Fusion (Freiburg) format: ctt cta gat ggc cgg c
  3. Add the following sequence to the beginning of the reverse primer (i.e. the reverse complement of the end of your insert):
    • Fusion (Freiburg) format: act agt att aac cgg t
  4. Order your primers...
 useful links for primer design:
 * OligoCalc -- doesn't offer all salt parameters
 * Phusion annealing Temperature calculator
 * CLC workbench has a very nice primer design tool

II PCR reaction

The initial PCR cycles allow the inner part of the primers to anneal. We then switch to two-step PCR since the primers can anneal along their full length to the products of the first rounds.

Note on annealing temperature: The HotStart Phusion enzyme requires annealing temperatures of 60°C or higher. The actual annealing temperature should be 3°C above the lower temperature calculated for any of the two primers. See also the In-Fusion instructions.

100µl single reaction 3.5xMaster 10xMaster
H2O 76µl 266 760
5x HF Buffer 20µl 70 200
10mM dNTP 2µl 7 20
FW primer 100 µM 0.5µl 1.75 5
RV primer 100 µM 0.5µl 1.75 5
Phusion 1µl 3.5 10
template DNA 0.1µl -- --
PCR Program
30"@98°C
5x (10"@98°C; 15"@Ta; text@72°C);
25x (10"@98°C; text@72°C);
10'@72°C
∞ 4°C
  • extension time text = (kb insert length) × 25"
  • annealing temperature Ta = (primer annealing) + 3°C

III Post-Processing

  1. add 1µl DpnI, mix well, incubate for 1h @ 37°C
  2. verify PCR result on an agarose gel
  3. desalt and purify with PCR purification kit

IV In-Fusion reaction

Follow standard Infusion protocol -- add a control with vector-only and one with insert-only DNA:

  1. mix vector and insert DNA in molar ratio of 1:2 into 10µl ddH2O
  2. add DNA mix to Dry-Down Infusion tube
  3. let stand for a minute
  4. carefully pipette up & down until dry-down mix is disolved
  5. put tubes into PCR device and run:
  6. stop reaction with 30µl 10mM TE Buffer

Check the details above against In-Fusion protocol

V Transformation

Follow the standard transformation protocol.

Note: Standard Top10 cells show rather low transformation efficiencies with In-Fusion products. We have had good experiences with Invitrogen MaxEfficiency DH5alpha cells and others report good results with Clonetech FusionBlue competent cells.

VI Screening

The positive transformation plates should have much more colonies than the control. Screen by colony PCR with the standard BBVF2 and BBVR primers; inoculate positive clones over night for miniprep, restriction test and sequencing.

Notes

Please feel free to post comments, questions, or improvements to this protocol. Happy to have your input!

raik: This protocol is quick and robust in my hands.


References

Contact

or instead, discuss this protocol.

Personal tools