SBB09Ntbk-Madhvi Venkatesh

Madhvi Venkatesh 14:54, 2 February 2009 (EST)

Today, I got my project ball and I am making a new flagellar display system. I need to consider several possibilities and figure out what would be best to make and the source. The project description if on this page: new flagellar display system

Madhvi Venkatesh 15:40, 9 February 2009 (EST)

Possible places to find EtpA homolog (from CTEC):

APEC 01:k1
CFT073
EHEC 0157:H7
Shigella flexneri

Madhvi Venkatesh 15:24, 23 February 2009 (EST)

So I rewrote my construction files after I realized that I can't display a protein on the N and C terminal ends of fliD because they are not facing the surface. The new versions of the construction files including Chris's notes on them are linked from the construction files page. We got oligos last Wednesday and I set up PCRs for the N and C terminal parts and wobble PCRs for the linkers. I purified and digested over the weekend. I also set up the SOEing PCR at the end of last week. Today I ligated the parts into pBca1256 and transformed. I will pick colonies tomorrow and send for sequencing on Wednesday. I also purified and digested the SOEing PCr for removing the restriction site in the N terminal fliD part.

Here are gel pics from the PCRs:

Here is the result of the SOEing PCR for the M1000 part {<N.fliD!} with the restriction site removed:

Here are the results of the other PCRs:

Madhvi Venkatesh 21:23, 27 February 2009 (EST)

I digestion mapped my basic parts:

Lane	Plasmid	Clone	Enzyme 1	Enzyme 2	Expected Bands	Result
1	pBca1256-M10000	1	EcoRI	XhoI	986 + 2113	correct
2	pBca1256-M10000	2	EcoRI	XhoI	986 + 2113	correct
3	pBca1256-M10001	2	EcoRI	XhoI	986 + 2248	correct (not completely digested)
4	pBca1256-M10002	2	EcoRI	XhoI	986 + 1585	No DNA
5	pBca1256-M10002	1B	EcoRI	XhoI	986 + 1585	correct (not completely digested)
6	pBca1256-M10003	1B	EcoRI	XhoI	986 + 1582	correct (mostly undigested)
7	pBca1256-M10003	2B	EcoRI	XhoI	986 + 1582	correct

Based on this, I am sending M10000-1, M10001-2, M10002-1B, M10003-2B for sequencing.

Madhvi Venkatesh 14:46, 2 March 2009 (EST)

I got my sequencing data back and the results are up on my anderson lab sequencing page. M10000 and M10001 sequenced correctly and these clones are good to use. The wobble products, M10002 and M10003 did not sequence so well. The read for M10002 had Ptet, BBb scar and another short sequence in between the BglII and BamHI sites. The read for M10003 didn't have BglII or BamHI sites and just went from the EcpRI site to the part of the vector after the BamHI site. I double checked the protocols and it looks like I did everything correctly, so I think that it failed at the PCR step. I talked to Chris about the sequencing results and the low colony yield, and he suggested that I should try it again with Taq and/or DMSO and drop the annealing temp to 45. I set up four sets of reactions (one of each type for each wobble reaction):

• Taq/55/no DMSO
• Taq/55/DMSO
• Taq/45/no DMSO
• Taq/45/DMSO

The recipe I used for the reactions with DMSO:

 24 uL water
 5uL DMSO
 5 uL Taq Buffer
 5 uL 10x dNTPs (2 mM in each; 0.2 mM final conc)
 5 uL Oligo 1 (100uM)
 5 uL Oligo 2 (100uM)
 0.75 uL Taq DNA Polymerase

Madhvi Venkatesh 03:19, 12 March 2009 (EDT)

So I got virtually no colonies on the plates from all of those conditions. Chris was suspicious and told me to thoroughly check the construction files and the sequences on the sides of the tubes. Everything looked right, so he told me to go ahead and redesign the experiment using SOEing instead of assembly. I wrote up the new construction files on my construction file page and ordered the new oligos. I set up the first round of PCRs today and ran them on the following gel. Fragments A,B,C,and D are in the first four lanes in that order:

I think all of the fragments are the correct size (even though the ladder is a bit wierd) and I am going to set up the second set of PCRs right now with these fragments.