Sauer:ATPase assays

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
Line 29: Line 29:
'''Procedure.''' In our lab, we use a 96-well plate reader that measures A<sub>340 nm</sub> over time in a 50 &mu;L reaction volume.  Stocks of 20X concentrate are pre-prepared and can be frozen at -80&deg;C until use.
'''Procedure.''' In our lab, we use a 96-well plate reader that measures A<sub>340 nm</sub> over time in a 50 &mu;L reaction volume.  Stocks of 20X concentrate are pre-prepared and can be frozen at -80&deg;C until use.
-
# Prepare the stock solutions below and aliquot the appropriate volumes of each into 100 &mu;L  aliquots:
+
*Prepare the stock solutions below and aliquot the appropriate volumes of each to make the 20X ATPase reaction buffer, which is stored in 100 &mu;L  aliquots:
{|border="1"
{|border="1"
-
|-
 
|10 &mu;L || 3750 U/mL pyruvate kinase  
|10 &mu;L || 3750 U/mL pyruvate kinase  
|-
|-
Line 42: Line 41:
|25 &mu;L || 200 mM ATP
|25 &mu;L || 200 mM ATP
|-
|-
-
|-32 &mu;L || dH<sub>2</sub>O
+
|32 &mu;L || dH<sub>2</sub>O
-
|-
+
|}
|}
 +
* Add your enzyme to a 1X aliquot of the ATPase reaction buffer in a 50 &mu;L total volume; mix thoroughly.
 +
* Monitor A<sub>340 nm </sub> and calcuate the ATPase rate using the above formula.
-
''will get back to this...''
+
(''Note: It's easier to thoroughly mix your reaction if you use equi-volumes of enzyme and buffer; you may want to start with a dilution to 2X ATPase reaction buffer.'')

Revision as of 01:55, 15 November 2006

SAUER LAB

Home        Protocols        Lab Members        Materials        Equipment        Links        Internal       


Principle. We use a system that couples ADP formation (from an ATPase of interest) with classical metabolic reactions to quantify ATP hydrolysis rates, as referenced in Norby, JG (1988) Meth enzy, 156, 116-9. The basic principle can be summarized below:


(1) ATP ⇔ ADP + Pi

(2) ADP + phosphoenolpyruvate ⇔ ATP + pyruvate

(3) pyruvate + NADH + H+ ⇔ lactate + NAD+


where reaction (1) is catalyzed by your ATPase, reaction (2) by pyruvate kinase, and reaction (3) by lactate dehydrogenase. Loss of NADH (as monitored by absorbance at 340 nm) is quantifiably proportional to ATP hydrolysis rates because this set of reactions begins with equilibria strongly favoring the forward direction and neither reactions (2) or (3) are rate-determining.


Calculating the ATPase Rate.


T\!otal\mbox{ }AT\!P\!ase\mbox{ }rate = \frac {rate\mbox{ }of\mbox{ }A_{340nm}\mbox{ }signal\mbox{ }loss} {pathlength * 6.23 mM^{-1}cm^{-1}}


By applying the above formula, you'll get some rate expressed in mM per unit time. For the molar activity (i.e., rate per mole of enzyme) simply divide this rate by the enzyme concentration you used in the assay. This will give you a hydrolysis rate in units of per unit time per enzyme.


Procedure. In our lab, we use a 96-well plate reader that measures A340 nm over time in a 50 μL reaction volume. Stocks of 20X concentrate are pre-prepared and can be frozen at -80°C until use.

  • Prepare the stock solutions below and aliquot the appropriate volumes of each to make the 20X ATPase reaction buffer, which is stored in 100 μL aliquots:
10 μL 3750 U/mL pyruvate kinase
10 μL 4290 U/mL lactacte dehydrogenase
8 μL 250 mM NADH
15 μL 1 M phosphoenolpyruvate
25 μL 200 mM ATP
32 μL dH2O
  • Add your enzyme to a 1X aliquot of the ATPase reaction buffer in a 50 μL total volume; mix thoroughly.
  • Monitor A340 nm and calcuate the ATPase rate using the above formula.

(Note: It's easier to thoroughly mix your reaction if you use equi-volumes of enzyme and buffer; you may want to start with a dilution to 2X ATPase reaction buffer.)

Personal tools