Smolke:Protocols/Insert prep

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
Line 1: Line 1:
 +
{{Smolke_Top}}
 +
 +
==Protocol==
*Prepare 5 x 100-ul PCR reactions for each insert
*Prepare 5 x 100-ul PCR reactions for each insert
**400 ul water
**400 ul water
Line 8: Line 11:
**250 ng plasmid
**250 ng plasmid
**10 ul 1:10 Taq DNA polymerase
**10 ul 1:10 Taq DNA polymerase
-
*Taq amplifies at 1000-2000 bp/min, so adjust extension time accordingly
 
*After PCR, combine products from the five tubes, and run 5 ul on a gel to verify product length
*After PCR, combine products from the five tubes, and run 5 ul on a gel to verify product length
*Purify and concentrate PCR products by phenol-chloroform extraction and ethanol precipitation
*Purify and concentrate PCR products by phenol-chloroform extraction and ethanol precipitation
*Resuspend inserts to appropriate volume for digestion reaction
*Resuspend inserts to appropriate volume for digestion reaction
 +
 +
==Notes==
 +
*Amplification rates:
 +
**Taq: 0.5-1 min/kb (YC). 1 min/kb (JKM)
 +
**Pfu: 2 min/kb (JKM)
 +
**PfuUltra: 1 min/kb (JKM)
 +
**PfuUltraII: 0.25 min/kb (JKM)
 +
**MutazymeII: 2 min/kb (JKM)
 +
 +
*Size: I consider this ''massively'' oversized. In my experience, 50uL of PCR products (~3ug product) is more than sufficient for cloning. -Josh
 +
*Polymerase: I use Pfu (>500bp) or PfuUltraII (>~3kb) for any lengthy PCR that I intend to clone. -Josh
 +
*Magnesium: I have never felt a need to vary my magnesium concentration on a reaction-by-reaction basis. So I mix my Taq buffer using a standard amount of magnesium (2mM, personally), and save an extra step. The magnesium concentration given above (0.16mM) seems ''way'' too low. -Josh

Revision as of 13:45, 15 October 2009

Home        Contact        Internal        Protocols        Lab Members        Publications        Research       


Protocol

  • Prepare 5 x 100-ul PCR reactions for each insert
    • 400 ul water
    • 50 ul 10x Taq buffer
    • 16 ul 5 mM MgCl2
    • 10 ul dNTP
    • 10 ul Fwd primer
    • 10 ul Rev primer
    • 250 ng plasmid
    • 10 ul 1:10 Taq DNA polymerase
  • After PCR, combine products from the five tubes, and run 5 ul on a gel to verify product length
  • Purify and concentrate PCR products by phenol-chloroform extraction and ethanol precipitation
  • Resuspend inserts to appropriate volume for digestion reaction

Notes

  • Amplification rates:
    • Taq: 0.5-1 min/kb (YC). 1 min/kb (JKM)
    • Pfu: 2 min/kb (JKM)
    • PfuUltra: 1 min/kb (JKM)
    • PfuUltraII: 0.25 min/kb (JKM)
    • MutazymeII: 2 min/kb (JKM)
  • Size: I consider this massively oversized. In my experience, 50uL of PCR products (~3ug product) is more than sufficient for cloning. -Josh
  • Polymerase: I use Pfu (>500bp) or PfuUltraII (>~3kb) for any lengthy PCR that I intend to clone. -Josh
  • Magnesium: I have never felt a need to vary my magnesium concentration on a reaction-by-reaction basis. So I mix my Taq buffer using a standard amount of magnesium (2mM, personally), and save an extra step. The magnesium concentration given above (0.16mM) seems way too low. -Josh
Personal tools