# User:Andrew K Farag/Notebook/Andrewfarag/2013/09/10

(Difference between revisions)
 Revision as of 19:36, 2 October 2013 (view source) (→Notes)← Previous diff Revision as of 20:24, 2 October 2013 (view source) (→Notes)Next diff → Line 63: Line 63: [[Image:Horseradishtrial1.png]] [[Image:Horseradishtrial1.png]] [[Image:Horseradishtrial2.png]] [[Image:Horseradishtrial2.png]] + [[Image:Concvsabs640nm.png]]

## Revision as of 20:24, 2 October 2013

Biomaterials Design Lab Main project page
Previous entry      Next entry

## Objective

The primary way of determining protein concentration is through a measurement of the protein's UV-Vis spectrum and using its molar absorptivity at 280nm to calculate concentration. For low concentrations of proteins, UV-Vis of just the protein is often not sensitive enough to accurately measure concentration. During the semester, we may need to measure protein concentrations that are very low. One chemical tool that we can use to do this is called the Bradford Assay. The Bradford Assay makes use of the Coomassie Blue dye, which binds to proteins. Upon binding to a protein, this dye undergoes a change in its absorption features. (No protein: peak at 460. Protein: peak at around 600). We will be making calibration curves (using the Bradford Assay) for the different proteins we'll be using throughout the semester.

## Description

The basic protocol that we will be using for this procedure can be found here. (*Note: use section 2.3, page 5)

1. Make a stock solution that is roughly 10mg protein in 2mL of buffer. (there are 2-2mL volumetric flasks that you will have to share)
2. Calculate what your actual concentration
3. Make 6 standard solutions (1mL each) between 1μg/mL and 10μg/mL
1. Determine the appropriate volume of your stock to use (for the proper final concentration in 1mL) and add that volume to an eppendorf tube
3. Add the correct amount of buffer such that the final volume is 1mL
4. Close the tubes and vortex them.
5. Let them sit for 5 minutes
4. Take a UV-Vis (no less than 1 hour after they were produced).
1. Use the plastic cuvettes.
5. Make 2 blanks as well (800uL buffer and 200uL Assay reagent) and take it's UV spectrum. (400nm-800nm)
1. We will be using one of the blanks as a reference for each spectrum that we take. I'll show you where to place this cuvette for each spectrum you collect)
6. After you have finished one set, repeat the process (make new samples and new measurements)

- Note: This is where coordination is a good thing. Take 1 spectrum at a time. Let other people go.

1. Make a calibration curve.
2. Determine if you need to redo any data or sample prep.

Note - Solutions from today containing the stain will go into a waste container in the hood.

We are also going to make Atomic Absorption standards for tomorrow!

Using the gold AA/ICPMS standard solution make 5 new solutions (Note: Use water - NOT BUFFER - to make these solutions)

1. 25 ug/mL
2. 20 ug/mL
3. 15 ug/mL
4. 10 ug/mL
5. 5 ug/mL

## Data

Making buffer: 1L 50mM Tris 50mM NaCl pH 7.5

Should mass out:

1. 6.057g Tris
2. 2.922g NaCl

Actually measured:

1. 6.0596g Tris
2. 2.9525g NaCl

Gold solution for group: HAT to make nano particles

1. Gold solution (HAuCl4·3H2O) 0.0050g in 0.0500mL water → 0.25mM

## Notes

Use categories like tags. Change the "Course" category to the one corresponding to your course. The "Miscellaneous" tag can be used for particular experiments, as instructed by your professor. Please be sure to change or delete this tag as required so that the categories remain well organized.