User:Darrell Bonn/Notebook/307L Lab book/OScope

Lab 1: Oscilloscope

Osciloscope Lab Summary

Brief summary of what you did (linking to the lab manual page is OK) Add links to all wiki pages that contain your notebook entries. This is likely only one page. Report your value for the fall time using AC coupling. Include uncertainty in your measurement! Explain how you measured this (briefly) What did you learn? It's OK if you didn't learn anything. But include things you are still finding confusing. What did you explore outside of the standard lab procedure? Anything interesting? What could make the lab better next year?

I used an oscilloscope and a function generator to get some practical experience measuring signals with an oscilloscope. Using the function generator to supply sine, square and triangle waves, primarily at 500Hz with 6v amplitude, I measured these by eye, with the cursors and with the automatic measuring functions. Then I played with the trigger functions, going through available trigger settings to see the effects the triggers had on data display. Then I measured the time time constant of the oscilloscope by setting a low frequency (70Hz) with AC coupling and measuring the fall time to 10% signal. I found this to be between 61.5 and 62ms.

I learned the difference between AC and DC coupling both from a user standpoint and as to what the functional circuit within the scope is.

Data

BK Precision 4017A Function Generator Tektronix TDS 1002 60MHz, 1GS/s Digtal O-Scope

Basic Waveform Data: Measuring sine wave in from the function generator 4017A Settings: 500 Hz, Level? No readout for output level TDS1002: Channel 1 input, DC Coupling, 1V/Division, 1ms/division

Turned function generator output level full down, connected to the oscope Slowly increased output till I found a good sine wave. Played with coupling a bit - AC/DC until a good display was available either way

Measuring by mark 1 eyeball - Able to clearly see 5 cycles taking the expected .5ms each Power level: 6v peak to trough

Measuring with cursors Voltage is 6.04 peak to peak (cursor resolution is .04V). Period is 2ms (freq = 500Hz) (cursor resolution is .04ms). Measurement made across 4 cycles and across 1 cycle (no variation)

Measuring with automatic functions Frequency ranges from 501 to 502Hz, (Period of 1.992 - 2.000ms) Peak to Peak 6.04V to 6.08V

Used the FFT to check signal purity. Primary signal is stable, 2'nd frequency is down 32dB, most noise below 45dB

Data acquisition shows a fairly stable signal Calculate frequency and voltage stability?

Repeating measurements with a square wave - all other settings on function generator unchanged Changed oscope display to 250us resolution

By eye: Period is about 1.95 ms (line just off the 2ms line). Voltage is 6.1V By Cursor: 1.980ms, 505.1Hz, 6.28V peak to peak By Auto Measure: 503.8-504.3 Hz, 1.983 - 1.985ms, 6.28VPeak to Peak

repeat with saw tooth, no instrument changes By eye: Period is right at 2ms, 500Hz; Amplitude is 5.95V By Cursor: Period is 2ms, 500Hz; Amplitude is 5.92V By Auto Measure: Period is Frequency is 501.03-501.08Hz, Amplitude is 5.96V peak to peak

Triggering: Rising edge means that the trigger occurs as the signal passes the threshold on the way up Falling edge means it looks for the threshold going down With a constant signal this will shift the phase by 180 degrees.

AC/DC Coupling -

Lecture: power, resistor, capacitor Meausruring with vscope across capacitor - slow rise, no fall off - DC coupling (good to measure DC signal - ) Measuring with vscope across resistor - fast rise, slow fall off - AC coupling (has a bit of a hi pass filter)

Data: Applied a large (10V) signal to the scope AC coupling reveals ripples and uneven qualities in the waveform DC coupling removes the small changes showing a stable square wave

Measuring the time constant Set function generator to 40Hz, square wave, amplitude about 8.6v all measured with DC coupling to confirm Switched to AC coupling. Measured the Peak of the waveform at 8.48V Measured the 3db drop off (4.24V) at 16ms Measured to the 90% drop off: .424V (.400 was limit of cursor value) at about 72ms

Using measure key I get 115.6ms (that's all the way to the end, not the 10% point) This was in error - the fall time measurement was innacurate and flagged so with a question mark Adjusting the frequency up to 70 Hz allowed for a fall time that was right at 90%. This measured a fall time of 61.5-62ms

From wikipedia page [| rise time] rise time (or fall time in this instant, they are symetric in this situation) rise time = approximately 2.197 tau tau = RC so rise time of 62ms indicates an RC of approximately 28.2

Setup

• Entry One

1. Indent one title
   • Sub One
   • Sub Two
   • Sub Three
   1. Indent Two Title
      • Sub One
      • Sub Two
      • Sub three