User:Jared A. Booth/Notebook/Physics 307L/2009/10/12

(Difference between revisions)
 Revision as of 21:39, 25 October 2009 (view source) (→Theory)← Previous diff Revision as of 21:41, 25 October 2009 (view source) (→Purpose)Next diff → Line 10: Line 10: ==Purpose== ==Purpose== 1) To demonstrate the wave properties of electrons.
1) To demonstrate the wave properties of electrons.
- 2) Examine the DeBroglie relation $\lambda = \frac {h}{p}$
+ 2) Examine the de Broglie relation $\lambda = \frac {h}{p}$
3) To measure the diffraction planes of graphite.
3) To measure the diffraction planes of graphite.

Revision as of 21:41, 25 October 2009

Project name Main project page
Previous entry      Next entry

Electron Diffraction

Purpose

1) To demonstrate the wave properties of electrons.
2) Examine the de Broglie relation $\lambda = \frac {h}{p}$
3) To measure the diffraction planes of graphite.

Theory

 In 1924, Lois DeBroglie proposed that as photons can be seen as both waves and particles, so too can electrons.Specifically, he postulated that the wavelength of ALL particles was related to their respective momenta by what is now known as the DeBroglie relation.


Equipment

• Tel 2501 Universal stand
• Electron Diffractor 2555 (5Kv .3mA)
• Teltron Limited London England 813 KV Power Unit
• HP 6216B Power Supply
• Wavetek Meterman 85XT multimeter
• Carrera Precision 6" digital caliper alloy. Note: the digital caliper's battery was low, so it was used as a standard caliper instead.

Safety

1. The main safety concern during this procedure is electrical shock as high voltages(813KeV power supply) will be used. Standard high voltage safety precautions should be taken, including checking all equipment for damage and ensuring the equipment is properly connected.
2. The second concern is the integrity of the equipment. Most importantly, the graphite diffraction tube. As indicated in the lab manual, the graphite is extremely thin and can be easily punctured by current overload. Use the multimeter to ensure the current stays below the maximum allowed current (0.25mA). Additionally, check the target regularly during the experiment for a red glow, indicative of current overload.

Procedure

The procedure should be followed from the Lab Manual experiment 3, electron diffraction.

The following circuit was set up, with the following modification: The low voltage bias was inverted; a multimeter was put in series between the positive HV source and plug G7 on the mount to measure current. NOTE: the max voltage measurable by the multimeter is 1000V. It is important to only measure current with the multimeter while it is connected to prevent damage to the instrument as up to 5kV will be used in this experiment.

Image taken from here

Raw Data

Voltage (kV) Inner Radius (mm) Inner Diameter (mm) Outer Radius (mm) Outer Diameter (mm)
4.8 n/a 22.5 n/a 41.75
4.77 12.5 n/a 20.0 n/a
4.70 12.0 22.75 20.5 41.5
4.60 12.5 23.5 21.5 42.1
4.50 13.0 23.75 21.75 42.5
4.40 12.75 25.0 21.25 42.5
4.30 12.25 24.0 21.1 43.0
4.20 12.5 25.25 21.5 42.5
4.10 12.75 24.7 21.25 43.1
4.00 14.2 24.3 23.25 44.5
3.75 13.0 25.75 23.5 46.0
3.50 14.0 27.0 23.0 48.5
3.25 14.0 27.7 24.0 51.1
3.00 14.5 28.5 25.0 53.1
2.75 15.0 31.8 25.5 54.25
2.50 n/a n/a n/a n/a