User:Klare Lazor/Notebook/Chem-496-001/2012/09/19

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(Description)
(Objective)
Line 11: Line 11:
==Objective==
==Objective==
#Crosslink the prepared glutaraldehyde film
#Crosslink the prepared glutaraldehyde film
-
#Run DSC on 8 films
+
 
-
#Run FTIR
+
# Repeat the crosslink of glutaraldehyde film
# Repeat the crosslink of glutaraldehyde film

Revision as of 08:49, 3 October 2012

Biomaterials Design Lab Main project page
Previous entry      Next entry


Objective

  1. Crosslink the prepared glutaraldehyde film
  1. Repeat the crosslink of glutaraldehyde film

Description

General Protocol 1(klare and Liz):

  1. Allow the glutaraldehyde PVOH film to completely air dry
  2. Prepare a solution of 100mL H2O, 2mL concentrated H2SO4, and 20g Na2SO4 in a 150mL beaker. Place stir bar in beaker and a Buchner funnel top (cap) over the stir bar
  3. Heat the prepared solution to 70°C(on hot plate turn temperature to 160°C)
  4. Place film in solution for 1 hour.(Make sure the temperature remains at 70°C) Must be under fumehood because of glutaraldehyde
  5. Prepare 100mL 1% aqueous HCl solution. Heat solution to 70°C. (ie: 1ml of HCL in 100 ml)
  6. Remove film from the solution and rinse with deionized H2O
  7. Place stir bar in 1% HCl solution and a Buchner funnel top over of the stir bar. Add the PVOH film to the solution
  8. Allow film to remain in 1% HCl solution for 30 minutes.(Be sure to keep a constant 70°C)
  9. Prepare 0.2M sodium bicarbonate solution
  10. After 30 minutes, remove film from 1% HCl solution and place in 0.2M sodium bicarbonate solution for ~15minutes
  11. Remove film from dilute sodium bicarbonate solution with tweezers. Rinse with deionized H2O and dry film on paper towel(dabbing gently).
  12. Weigh PVOH film. Record mass= .8059g

General Protocol 2 (Noah):

  1. Repeat Glutaraldehyde film prep
  2. make 2nd glutaradehyde film film, except and replace 10% PVOH with PDMS
  3. Prepare 1 L glutaraldehyde solutions
  4. prepare 500ml 20ppm SO42- as CuSO4
  5. prepare 500ml 20ppm SO42- as Na2SO4
  6. dry clays

Glutaraldehyde Prep and CuSO4*5H20 20ppm

  • 0.5g PVOH, 5ml H2O => dissolve
  • add 1ml Glutaraldehyde in fume hood
  • 0.5132 g PVOH, 5ml h2o + 1ml glutaraldehyde
  • 0.4055g PVOH, 0.1015 PDMS, 5ml h2o

*200 g Na2So4, 1L H2O stirred to dissolution + 20ml H2 So4 *MW CuSO4 * 5 H20= 249.67 g/mole 20 ppm in 500ml H2O MW= 18 g/mol (500g of h20/18g/mol=27.7moles) **27.7moles h2O* ((20moles cuso4*5H2O)/1,000,000 moles H2O) = 5.55 E -4 moles Cuso4*5molesH20 **5.55E-4moles CuSo4*5H2O * 249.68 g/mol= 0.1387g CuSo4*5H2O **5.55E-4moles Na2SO4 * 142.04g/mol=0.078 (20ppm)

  • we want 500ml of 20ppm = 20mg/l CuSO4
    • 277.4mg/l*x=.5*20mg/l
    • x=36.05ml in total 100ml solution
  • we want 500ml of 20ppm= 20mg/l Na2SO4
    • 156.8 mg/l x = .5(20mg/L)
    • x= 63.78ml in total 100ml solution

Data

  • Add data and results here...

Notes

This area is for any observations or conclusions that you would like to note.


Use categories like tags. Change the "Course" category to the one corresponding to your course. The "Miscellaneous" tag can be used for particular experiments, as instructed by your professor. Please be sure to change or delete this tag as required so that the categories remain well organized.


Personal tools