User:Moira M. Esson/Notebook/CHEM-581/2012/09/07: Difference between revisions
From OpenWetWare
(fix raw html notebook nav) |
|||
(5 intermediate revisions by 2 users not shown) | |||
Line 2: | Line 2: | ||
|- | |- | ||
|style="background-color: #EEE"|[[Image:owwnotebook_icon.png|128px]]<span style="font-size:22px;"> Project name</span> | |style="background-color: #EEE"|[[Image:owwnotebook_icon.png|128px]]<span style="font-size:22px;"> Project name</span> | ||
|style="background-color: #F2F2F2" align="center"| | |style="background-color: #F2F2F2" align="center"|[[File:Report.png|frameless|link={{#sub:{{FULLPAGENAME}}|0|-11}}]][[{{#sub:{{FULLPAGENAME}}|0|-11}}|Main project page]]<br />{{#if:{{#lnpreventry:{{FULLPAGENAME}}}}|[[File:Resultset_previous.png|frameless|link={{#lnpreventry:{{FULLPAGENAME}}}}]][[{{#lnpreventry:{{FULLPAGENAME}}}}{{!}}Previous entry]] }}{{#if:{{#lnnextentry:{{FULLPAGENAME}}}}|[[{{#lnnextentry:{{FULLPAGENAME}}}}{{!}}Next entry]][[File:Resultset_next.png|frameless|link={{#lnnextentry:{{FULLPAGENAME}}}}]]}} | ||
|- | |- | ||
| colspan="2"| | | colspan="2"| | ||
Line 35: | Line 35: | ||
|} | |} | ||
'''Note''':Complete dissolution of the PVOH required a longer amount of stirring(~2hours) and the addition of more deionized H<sub>2<sub/>O. To prompt complete dissolution, solutions were transferred to larger beakers(~50mL) with larger amounts of H<sub>2<sub/>O. | '''Note''':Complete dissolution of the PVOH required a longer amount of stirring(~2hours) and the addition of more deionized H<sub>2<sub/>O. To prompt complete dissolution, solutions were transferred to larger beakers(~50mL) with larger amounts of H<sub>2<sub/>O. | ||
==Crosslinking PVOH Films== | ==Crosslinking PVOH Films== | ||
Standard Protocol for Crosslinking of films: | Standard Protocol for Crosslinking of films: | ||
Line 72: | Line 73: | ||
DSC will be used to determine the different thermal transitions of the various films | DSC will be used to determine the different thermal transitions of the various films | ||
'''General Protocol for DSC:''' | '''General Protocol for DSC:''' | ||
#Weigh out the mass of a Tzero pan+Tzero lid(Record this measurement) | # Weigh out the mass of a Tzero pan+Tzero lid(Record this measurement) | ||
# | # Cut and weigh out ~ 280 - 320mg of PVOH film sample to place in the Tzezo pan | ||
# Once each sample is placed in the pan, then place the lid onto the pan | |||
# Use a Tzero press to secure and press the lid tightly over top the sample within the pan | |||
# Open TA instrument explorer on computer. Select instrument to be used(in this case DSC) | |||
# On control button, click event to create a new event | |||
# To create a new event or run, click either the apply or append commands | |||
# To modify a run, go to the experimental command and run a method edit | |||
# Save all changes made to an experimental run in order to analyze samples | |||
<br> | |||
To Collect the information from the DSC: | |||
# Click on export data file command | |||
# Go to file and plot signals command | |||
# Export the information obtained and save it(if possible save on flash drive) | |||
# Go to signals command and select signal section, then time command underneath | |||
# Select the analyze data command, then afterwards the integrate peaks command underneath | |||
# Accept values established by integrating the peaks | |||
# Click the analyze data command again to assign the glass transition value | |||
# Select the area in which the glass transition point is seen and integrate that information | |||
# Accept the values established from the glass transition point | |||
* About 3 mg ± 20% PVOH film was placed in a DSC pan. | * About 3 mg ± 20% PVOH film was placed in a DSC pan. | ||
Line 86: | Line 103: | ||
** Sample mass: 3.15 g | ** Sample mass: 3.15 g | ||
* [[Media:PVOH(22K), 15%M, H3PO4.pdf|Graph of heat flow of uncrosslinked PVOH (MW 22000) + 15% maleic acid + H<sub>3</sub>PO<sub>4</sub>]]. | * [[Media:PVOH(22K), 15%M, H3PO4.pdf|Graph of heat flow of uncrosslinked PVOH (MW 22000) + 15% maleic acid + H<sub>3</sub>PO<sub>4</sub>]]. | ||
** Two possible glass transitions at 105.79°C and at 155.16°C were observed(able to observe on graph by looking at the change in slope). Running DSC on the sample a second time may clarify which is the true glass transition temperature. | |||
** Two sharp peaks at 144.66°C and at 155.64°C were observed. A reaction may have occurred at these temperatures or a phase change may have occurred | |||
* [[Media:PVOH(22K), H3PO4.pdf|Graph of heat flow of uncrosslinked PVOH (MW 22000) + H<sub>3</sub>PO<sub>4</sub>]]. | * [[Media:PVOH(22K), H3PO4.pdf|Graph of heat flow of uncrosslinked PVOH (MW 22000) + H<sub>3</sub>PO<sub>4</sub>]]. | ||
** A glass transition was observed at 82.61°C. | |||
** A sharp peak was observed at 179.47°C. This may be caused by a reaction or phase change. | |||
==Notes== | ==Notes== |
Latest revision as of 21:59, 26 September 2017
Project name | Main project page Previous entry Next entry | ||||||||||||||||||||||||||||||||||||||||||||||||||
Objectives
PVOH(MW 130,000) Films
Prepared PVOH(MW 130,000) Films
Note:Complete dissolution of the PVOH required a longer amount of stirring(~2hours) and the addition of more deionized H2O. To prompt complete dissolution, solutions were transferred to larger beakers(~50mL) with larger amounts of H2O. Crosslinking PVOH FilmsStandard Protocol for Crosslinking of films:
Crosslinked PVOH Films:
Solubility of PVOH FilmsGeneral Protocol:
Viscosity of uncrosslinked PVOH(MW 22,000) 15wt% maleic acid
DSC on PVOH FilmsDSC will be used to determine the different thermal transitions of the various films General Protocol for DSC:
Notes
Observations
|