Millikan Oil DropDH 1
To view the exact procedure used in this experiment or to learn more about the apparatus used, follow the given link to http://physicscourses.okstate.edu/flanders/phys3622/handouts/Millikan~oil~drop.pdf
Refer also to Antonio Rivera's page Physics307L F07:People/Rivera/Notebook. For photographs of our specific setup.
The purpose of the Millikan oil drop experiment is to measure the charge of an electron. This value is found by balancing the electric and gravitational forces on tiny oil drops sprayed in between two charged plates. By measuring the travel speeds of the oil drops both in an electric field and when left only to gravity, one should find values that are always integer multiples of a given amount. This amount is the charge of an electron (1.602 x 10^-19 C).
Equipment and SetupSJK 00:44, 10 October 2007 (CDT)
This particular version of the experiment utilized the PASCO Millikan oil drop apparatus. See link given at the top of the page for illustrations and a detailed description of this particular piece of equipment. The setup for this experiment was fairly straight forward. The only modification made to the instructions was to place the apparatus on top of a stack of books to make long viewing sessions a little more comfortable.
One issue did arise in the focusing of the viewing lens. The manufacturers suggested method for properly focusing the magnifying lens was slightly vague, and in the end completely useless. For the purposes of our experiment we found it to be much easier, and necessary, to focus the lens as we introduced oil drops into the chamber.
Data collection did prove to be slightly tricky as there was a definite learning curve associated with the use of this particular instrument. Initially oil drops were hard to find at all. Once this was accomplished, however, the trick was to pick out a quality drop in which good measurements could be taken. It seemed early on that the drops movements were erratic and unpredictable. It was from this that we discovered an error that we had been making in our data collection procedure. Because of this, I have broken my data into two sections based on how the data was taken.
Trial 1: Measurements 1-8
In measuring the rise and fall times of our oil drops it was necessary to set the oil chamber as to allow for positive pressure that would in turn "suck" selected drops into the viewing chambering in between the electrodes. This was done using a selector switch on the left side of the chamber. Once drops were viewed it was necessary to flip the switch down into the off position to begin the experiment. However, for our first set of numbers we were setting the switch instead in to the on position which served the purpose of introducing the chamber to a radioactive source, and introducing our oil drops to released alpha particles.
Trial 2: Measurements 1-9
These measurements were taken using the outlined procedure given in the PASCO operating manual
Values need for calculations
From Bradley's page Physics307L F07:People/Knockel/Notebook/070912
Known (given to as many significant figures as are reasonably certain): * (plastic spacer width using micrometer) * (density of oil given on bottle) * (gravitational acceleration) * (some stupid constant) * (length droplet will be measured over)
To be found when taking data:
*p (air pressure in Albuquerque. Changes by day will be read each day data taken) *T (temperature from thermistor in °C) *V (Voltage between plates in viewing chamber in volts) *tf (time droplet takes to fall in no field in seconds) *tr (time droplet takes to rise in field in seconds)
To be calculated later:
*η (viscosity of air as a function of T found in a table in Pa*s) * (average velocity of oil droplet falling in no field in m/s) * (average velocity of oil droplet rising in a field in m/s) * (radius of droplet in meters) * (charge of oil droplet in Coulombs)
Measurment # / q (per electron)
Trial 1SJK 01:21, 10 October 2007 (CDT)
Mean for Trial 1 = 1.6605E-19
Standard Deviation = 1.0205E-20
Standard Error = 3.6080E-21
Mean for trial 2 = 1.68078E-19
Standard Deviation = 1.16717E-20
Standard error = 6.7387E-21
ConclusionsSJK 01:25, 10 October 2007 (CDT)
1.) Issues with process - At one point I believe that Antonio and myself had figured out the best possible methods for taking data in this experiment (measurements 9 and 10). However, difficulties with the apparatus itself prevented more such data sets from being taken. This is to say that at one point our apparatus all together stopped working. Oil drops would no longer find there way into the chamber and the instrument would actually begin to smoke. I believed this to be some sort of possible clog in our system somewhere. This seemed to not be the case. It did appear that after prolonged use a cool down and wipe down might be necessary to keep the system functioning.
2.) Error Calculations - In the end I calculated the average charge per electron found from each measured oil drop. From this I calculated the mean, standard deviation, and standard error for the two individual trials. This seemed most appropriate for my current understanding of error calculation, but it does seem fairly insufficient. Our measurements only really concerned the oil drop velocities. This, however, is a small part of the final equation used in calculating the charge of the oil drops. It would seem that larger percentages of error would be possible in our measurements then there would be in the rest of the variables involved in our calculations. Discussing this with Prof. Koch brought up the subject of error propagation. I hope to eventually learn more about this and possibly extend it later on to the data I collected for this experiment.